RX8 Project – Part 9, Flywheels Part 3

So just to finish of the flywheel section here are the the finished custom parts :

Flywheel spacer on the crank, you can see the black dust seal in the centre covering the new pilot bearing underneath.Duratec V6 Crank Spacer

A wider shot showing the spacer in position among the currently disassembled state of the engine.Duratec v6 Flywheel spacer

And finally the flywheel itself.

Custom Duratec v6/RX8 Flywheel

In this photo the ring gear and location dowels for the clutch basket have been fitted.

The ring gear was actually a lot easier to fit than it was to remove because you can just put the ring gear in the oven (at maximum, in my case 250°C+ off the end of the scale!) and put the flywheel in the freezer for an hour or so as well – this may not actually be necessary but you want the most possible room between the parts when you fit them together. If the ring gear snags on the way down it because there isn’t quite enough space it can be a real pain to get it off again. Before installing the ring make sure it is the correct way round – all the teeth should have a bevel on one side to help the starter engage cleanly this goes towards the position of the starter motor! Take the hot ring out the oven, check it and drop it into place as quickly as possible but make sure it’s right and fully seated to the shoulder of the flywheel. Once touching the flywheel the ring will cool rapidly and lock in place.

The dowels in question turned out to be the wrong size, I specified them as 1/4″ diameter (6.35mm) and this is what is still shown on the drawing but it turns out the ones I measured had more rust than I thought and the holes in the clutch basket are actually designed to locate on 6mm dowels – something I really should have checked! From what I have since found out this is likely one of the many Ford engines which have special dowels which are  (from what I can find out) 8mm on the flywheel side but only 6mm on the clutch side. The correct dowels are actually 6.30mm on the smaller diameter so my original measurement wasn’t actually too far off, I just shouldn’t make daft assumptions! Larger end is 7.97mm diameter by 6.5mm long on the ones I have, overall length is 18mm. Tolerances and fits are not my strong point but I’ll probably start with a 7.9mm drill and hope to press fit them.

For simplicity I recommend buying something like this available via eBay as Cosworth clutch dowels by x-power engines:Xpower Flywheel Dowels

I’m planning to modify the appropriate holes on the flywheel to use the correct dowels I just haven’t quite got round to it yet!

I should probably also take a moment here to mention flywheel bolts. The Duratec crank has a slightly unusual thread which is M10x1.0mm (M10 Extra fine). This is as it happens the same thread commonly used on brake hydraulic components like bleed screws. Needless to say the stock bolts are far too short as the engine originally just had a thin flex plate so longer bolts were needed. Now various companies will sell flywheel bolts for almost any engine but not for something like this and they rarely specify the actual sizes of the bolts in a kit so I can’t just buy one for something else that will fit very easily. My solution was find the best standard bolt I could and so I am using some 12.9 high tensile socket cap bolts which I managed to find from a bolt supplier on eBay with the right thread. For anyone who doesn’t know 12.9 rated bolts are the highest rating before getting into one off special items (usually using exotic materials) and they really are very strong. As a comparison ARP gives their flywheel bolts as having a tensile strength of 180,000 PSI. The 12.9 bolts are rated to have a minimum tensile strength of 176,900 PSI – a number close enough it makes me think they are likely the same material! The strength figures for these bolts mean at the size I will be using each bolt can be safely loaded to in excess of 7000kg of tensile load indefinitely with no deformation. Their failure point being somewhere north of 9500kg each! Some time in the future I will do a full write up of nuts bolts and other fixtures it’s worth knowing about.

So that’s my shiny custom flywheel, next time you see it it should be bolted to a rebuild engine with a whole host of custom or cobbled bits on it!