After deciding to turbo the engine (see earlier posts) is became apparent I would have to upgrade the piston rods to make sure the engine wasn’t in danger of these failing and ruining the engine. This meant I needed to extract these from the engine Now bear in mind that this was the first time I’d ever taken the head off and engine before let alone removed a crank so it was likely to be quite a long and delicate process! Also accept that I was making this up as I went along, things may be in a strange order but it seemed to work!
First things first mount the engine to a suitable stand:
Here it is, it’s already upside down but that doesn’t matter! First off I took off the sump. On this engine it’s a cast alloy unit with a large front bulge which makes working around the front of the engine more awkward so I got it out the way early on.
Take off the oil pick up pipe (2xM6 bolts) to get room for the windage tray. The tray is held on by 5 nuts on some special studs on this engine, these are M10 one side to hold the lower block to the upper block but i think M5 on the top just to hold the windage tray.
Now we have exposed the moving parts of the engine and get the first look at the bits we are replacing but there’s a lot more before we get them all out. An interesting thing to note here is the absence of crank bearing caps. On this engine the block is formed in two cast pieces which joint along the crank centre line so the crank bearings are held in place by the substantial cast ribs you can see in the picture and each bearing has four M10 bolts to keep it in place with additional bolts around the outside of the casting.
Next move to the front of the engine and disconnect the hose from the block to the water pump then unbolt the water pump. On the Ford version of this engine the water pump is driven directly off one of the cams but on this Jaguar one it is a separate unit driven from the back side of the accessory belt and is held on by three small M6 bolts. Next up remove the crank bolt, there are a variety of ways to do this (the easiest probably being a decent impact gun but at this point in the project I’d not yet bought it) but the method I chose was to block the rotation of the crank using a block of wood. This is done by finding a suitable block that fits between the crank and the housing such that as the crank counterweight rotates round it is stopped by the wood. Just remember that the crank bolt undoes anticlockwise so make sure you put the block on the correct side(the bottom in the above image)!
Now you can flip the engine back up the correct way because we’re moving on to the heads This is because the cam covers need removing to take off the front engine cover.
This bit is again very simple, remove the bolts holding each coil unit in place. Again this being the Jaguar version of the engine is came from the factory with coil on plug. Next remove all the bolts around the cam cover and lift the cover away. Sometimes these get refitted with instant gasket to fix a failed cover gasket cheaply and quickly and so it may require some persuasion, I usually use a putty knife or a wallpaper scraper for this job but it can be easy to damage the faces if you’re not very careful. Alternatively plastic trim removal tools can work well. Obviously repeat the process for the other cover.
Next up we need to remove the front engine cover. This involves removing the bolts all the way round the edge, you can’t miss them, there’s loads and they’re all the same! Make sure you get them all, I think there’s 17 of them but don’t quote me on that, one is under the belt tensioner by the crank! This cover again might require a little help coming away due to the gasket but should be relatively easy. If it isn’t then you’ve missed a bolt so stop prying it!
It should look something like this! Now you can see the other feature these jag engines have – variable valve timing on the intake cams. An important point here is the crank timing wheel (the notched wheel on the crank). These have two key positions but only one is correct so carefully mark which position lines up with the key on the crank when you take it off. I recommend something permanent so when you clean all the oil residue off the mark is still visible, a centre punch mark should do it.
Next you need to remove the timing chain tensioners. These are small hydraulic cylinders that use engine oil pressure to maintain tension in the timing chain. They are held on by two bolts each. Just undo the bolts and carefully remove the tensioners from the tension arms.
Once the tension cylinders have been removed the tension arms can be lifted off their dowels and removed as well and then the chains can be lifted off and you should have something that looks a bit like this:
Now all that is clear the chain runners can be removed. These also hold the VVT solenoids and so are quite a complex bit of metal but are easily removed. I also took of the water hoses at this point just to simplicity.
Now you should be at this stage:
In the next part the engine strip will continue…
One thought on “RX8 Project – Part 14, Engine Strip #1”